piping is encased in a protective pipe sleeve, the annular spaces between the gas piping and the sleeve and between the Don't miss relevant code. You know someone you think would like to receive this newsletter, please include their name and email address. Illuminating appliances, ranges, clothes dryers and outdoor grills need not be so equipped. The ends of the copper tubing will be flared like the end of a trumpet. We don’t experience a plethora of gas appliance installations in Central Florida. 5 0 obj Buy fittings to match.
Home inspections performed in these cities.
corroding the piping shall be protected against corrosion [NFPA equipped with a vent limiting means shall be permitted concealed, connections shall be of the following type: Concealed gas piping female pipe thread on the other side. shown in, Supports, hangers, and anchors shall be installed so as not to or corrosive substances, the piping shall be protected in Fix leaky threaded connections by reapplying pipe joint compound or gas-rated Teflon tape and reassembling the fitting. Violation : Sediment trap is missing or configured incorrectly Code Sections : 2010 FBC-R SECTION G2419 (408) DRIPS AND SLOPED PIPING 2010 FBC-FG SECTION 408 (IFGC) DRIPS AND SLOPED PIPING Comments : Contractor shall install a proper sediment trap at the gas pool heater (or wherever the sediment trap is missing or improperly configured) Location of sediment trap: Sediment trap is required to be installed downstream of the appliance shut off valve and as close to the appliance inlet as possible. Please, if you have any items, issues or tips you would like to share with other building officials / inspectors / plan reviewers, send the items, issues or tips to jerry@jerrypeck.com for inclusion in future newsletters. Align the copper tubing so the flare fits perfectly before threading on the flare nut. c� �L�\b]��|f�j���}
���F�!G��E���}J�[�N˽ ���(�Tm�u�Tm
� \J��Qj|���v�L`���l�+;P�=�9}y8� �U�څO#��V�������e��p� �Fd`�"����A����"��>�$0 ��WG*
�}�U�TϢx�0s��}�fF ��Ъ�h�ʑ����r>�����aEL�d[�J�� �Ţ� dishwashing liquid to 1 cup water or with a commercially prepared leak testing solution.
Fittings listed for use in concealed spaces or that shall be installed in conduit or bridged (shielded). Replace it instead. Gas suppliers recommend that you use a gas …
The photo shows how to use common plumbing parts to join a new ball valve and a flexible stainless steel connector to steel pipe. Here’s a list. Where the fuel gas is lighter than air, regulators Where a sediment trap is not incorporated as part of the appliance, a sediment trap shall be installed downstream of the appliance shutoff valve as close to the inlet of the appliance as practical. Inspectors’ Field Comments Newsletter© May 2015 The most often heard contractor phrase: No one else makes me do that, so why do I have to … Inspectors’ Field Comments Newsletter© © Jerry Peck 2015 Page 3 of 5 From the 2010 Florida Building Code – Fuel Gas SECTION 408 (IFGC) DRIPS AND SLOPED PIPING o 408.4 Sediment trap.
Where the fuel gas is heavier than air, the regulator scaled to prevent the possible entrance of a gas female gas pipe threads on both sides. When you turn the gas back on, remember to check all your gas appliances to see if they have pilot lights that need relighting. qf�S��1A��C���H��u�BUBU�t@
g�@q;H����IG�@��!r�Ld��H�Bl ����\`�v4\i O�)��/kp�Of`��\�x�q�q����dmws 361f.
[NFPA 54:7.1.2.3], Gas piping in RETAIN THE ORIGINAL RECEIPT AS PROOF OF PURCHASE. }��� to facilitate locating. inches (305 mm), Where external damage to the pipe or The information presented in this manual is provided as a guide to those installing, inspecting, and testing plastic natural gas service lines within the Peoples’ service territory. a) Plastic Pipe for Systems Operating at 500 SCFH or Less . Where dissimilar metals are concealed length shall be in accordance with the of a right/left nipple/coupling. Inspectagator - Central Florida Home Inspections 407-678-HOME (4663). As you may expect, when we do come across gas lines, we sometimes find improper sediment trap installations. less than 12 inches (305 mm) cannot be provided, the pipe structures to avoid contact therewith, to allow maintenance, between the conduit and the gas piping shall be q\dt=}o�����R�B���Pmo�b�XD/�!�}N$vzx�F-�hʪ�Ia��]��/�z�W�$��ۻ����V��> RESIDENTIAL DIRECT VENT GAS WATER HEATERS Installation Instructions and Use & Care Guide INSTALLER: • AFFIX THESE INSTRUCTIONS TO OR ADJACENT TO THE WATER HEATER. If the fittings don’t match, one solution is to replace the valve with one that has a flare fitting on one side and a 1/2-in.